Cardiff and approved areas within about 20 miles, from Barry and Penarth to Caerphilly, Newport, Pontypridd and Bridgend.

‭07960 485 880‬ hello@handymancardiff.uk

Handyman Cardiff Repairs, fitting and maintenance across Cardiff

Why your bath sealant keeps going black, and the proper fix

Black sealant is not dirt. It is mould growing in and under silicone that has lost its seal, which is why cleaning it never works for long.

Why your bath sealant keeps going black, and the proper fix - article banner

It is one of the most common jobs we are asked about, and one of the most commonly bodged. A bead of silicone around a bath or shower tray goes black at the edges, somebody scrubs it, it comes back, somebody runs a new bead over the top of it, and six months later it is worse than before.

What is actually happening

Silicone is waterproof, but the joint it sits in moves. A bath full of water and a person is a lot heavier than an empty bath, and it flexes downwards by a surprising amount. Every time that happens, the bead is stretched. Eventually it parts company with the bath, the tile, or both, in places you cannot see. Water then gets behind it and stays there, and the mould you can see at the surface is growing in the damp gap behind the silicone rather than on it.

That is why cleaning does not fix it. You are cleaning the visible end of a problem that lives behind the bead. And it is why new silicone on top of old never works: silicone does not bond to cured silicone, so you have simply put a lid on a wet, mouldy gap.

What proper resealing involves

There is no shortcut, and the whole job is in the preparation.

  • Cut the old bead out completely. All of it, including the thin smear left behind, using a sealant knife and a solvent remover rather than brute force.
  • Clean and kill the mould. A mould treatment, left to work, then rinsed.
  • Dry the joint fully. This is the step people skip. Silicone applied onto a damp joint fails early, and a joint that has been wet behind the bead for years needs more than ten minutes.
  • Fill the bath before sealing, where it is right to do so. Sealing under load means the joint is at its widest when the silicone cures, so it is not stretched to breaking the first time somebody gets in.
  • Use a mould-resistant sanitary silicone, not a general-purpose or frame sealant, and run it as one continuous bead rather than in sections.
  • Leave it alone to cure. At least 24 hours before it gets wet, and the tube will say what it needs. This is the second step people skip, and it undoes everything above it.

Why the corners should never be grouted

While we are here: internal corners, and the junction between tiles and a bath, worktop or tray, should be silicone, not grout. Those joints move, grout is rigid, so it cracks, and then water gets behind the tiles. If your bathroom has grouted corners that keep cracking and going black, that is the reason, and swapping grout for sealant in those joints is a straightforward job that solves it permanently.

How to make it last

Ventilate. The single biggest factor in how long sealant and grout stay clean is how fast the room dries after a shower. Use the extractor fan, and check it actually vents outside rather than into the loft, which we find more often than you would believe. Open the window. Wipe the edge of the bath or the screen down occasionally. And if there is no fan, that is a worthwhile thing to have fitted by an electrician, because everything else in the bathroom lasts longer once the room dries properly.

When it is more than sealant

If there is a stain on the ceiling below, or the floor feels soft near the bath, the water has been getting through for a while and the repair is no longer cosmetic. Stop and get it looked at before resealing, because sealing over an active leak just hides it. The same goes for tiles that sound hollow when tapped: water behind the tiles has already loosened the adhesive, and new silicone at the edge will not change that.

Questions people ask

Can I just clean black sealant?
You can improve the look briefly, but the mould is growing behind the bead rather than on it, so it returns. Once it has gone black along a length, replacing it is the only real fix.
How long before I can use the shower after resealing?
At least 24 hours, and follow whatever the product says. Using it sooner is the most common reason a fresh reseal fails within months.
Should the corners be grouted or sealed?
Sealed. Internal corners and the joints with a bath, tray or worktop all move, and grout cracks. Those joints want sanitary silicone.
Why does my bathroom sealant go black so fast?
Usually ventilation. If the room stays wet for hours after a shower, mould has what it needs. Check the extractor works and that it vents outside rather than into the loft.

More from the blog

Call Request a quote